NOTE: Price includes a Link Plug In ecu control board installed onto the KO Racing Adapter with a KO Racing base calibration. The base calibration is intended only to get the vehicle started and running. Tuning by an experienced tuner will be required or possible serious engine damage could occur.

NOTE: This product is intended for tuning manual transmission vehicles and includes no provisions for automatic transmission control. It is intended primarily for vehicles that have swapped in the ST215 Caldina 3SGTE engine or ST215 Caldina ecu and engine control wiring.

NOTE: Can also be used on Gen4 3SGE Beams "Redtop" applications.

LINK G4X Plugin has the following Features:
(Click Here for full specifications.)

Features
• Configurable for 2-Stroke, 4 Stroke and Rotary Engines
• Configurable Firing Order
• 6 x High Current Injector Drives (suits high impedance injectors)
• 8 x Ignition Channels
• 8 x Auxiliary Outputs (All PWM capable). Aux5-8 can control Stepper Motors and drive High or Low
• 11 Digital Inputs (All capable of reading frequencies up to 10kHz)
• 4 Temperature Inputs (Configurable pull-ups on ANT1&2)
• 12 x 0-5V Analog Inputs
• 2 x Trigger Inputs (Reluctor, Optical or Hall Sensors)
• On Board Baro
• Traditional, Modelled and Modelled Multi-Fuel Equations
• Quick tune (automated fuel tuning)
• Up to 440 Zone Fuel Table with configurable load and RPM centers. Configurable X and Y Axis Parameters
• AFR Table Correction
• Individual Cylinder Fuel Trims
• Idle ignition control
• User Configurable RPM Limits based on external input
• MAP Limit with dual tables
• Selectable fuel or ignition limiting
• Each Output independently configurable
• Unused ignition and Fuel outputs available as auxiliary outputs
• Ethanol Sensor Control
• Wheel Speed Detection on all digital inputs with additional general-purpose speed inputs
• General Purpose switches, speeds, rpms and frequencies
• large variety of input types
• Built in 3 axis accelerometer
• Large number of built in calibrations as well as user configurable calibrations
• Supports nearly all OEM trigger patterns and custom trigger arrangements
• Anti Lag
• Launch control
• Solenoid, Stepper or EThrottle Control Idle control
• Open or Closed loop actuator control and Closed loop Ignition control available
• Has an internal EThrottle Controller and supports external controllers
• Open or Closed Loop Boost Control
• Boost control by Gear, coolant temperature, intake air temperature, etc.
• Built in Knock input and control for ignition and fuel on a per cylinder basis.
• Variable Valve Timing Control closed loop control for many OEM applications, or PID control for advanced tuners
• AC Control - Basic and Advanced modes available
• 512 Megabytes of Datalogging
• Up to 250 ECU Logging channels
• Up to 1kHz per channel with a maximum total sample rate of 100kSamples/s when using ECU Logging
• Unlimited channels when using PCLink logging
• Tuning Port USB on board
• Two CAN buses

Processing
• 150 MHz Specialised Engine Management Microprocessor
• Ignition control to 0.1 degree, fuel to 0.01 ms
• 32 Bit Floating Point Calculation
• 12 Bit ADC Resolution
• 20000+ RPM
• 4Gb Non Volatile Flash

Environment
• Internal Temperature Range -10 - 85oC
• Ambient Temperature Range -30 - 90oC
• Operating Voltage 8 - 22V Operating Current 200mA
• Electrical protection on all inputs and outputs
• Onboard Barometric Pressure Sensor

Typical Packaging Contents
• G4X PlugInX ECU
• Wiring and Installation Instructions
• 2 large Link Stickers
• 2 small Link Stickers
• Manufacturing Standard – ISO 13485

NOTE: This is not a LINK ECU tested, verified, and warranted product. Purchase of this product constitutes your consent with, and understanding of this statement. This is a custom adapter product that uses a part from a Link ECU. Please let KO Racing know if you have any questions or concerns, or require any support for our adapter board.